Toorak PaintersResidential House Painting (period & exterior repaints) · Toorak, VICGet in touch

Should You Paint Bluestone or Sandstone? Stonework on Toorak Homes

Stone is part of the character of the house

Many of the grand homes in Toorak, Kooyong and Armadale sit on stone. Victorian and Edwardian houses often have bluestone foundations and plinths, bluestone front steps and thresholds, and bluestone edging along paths and driveways. Some of the larger mansions and interwar homes also carry sandstone dressings: window sills, lintels, quoins at the corners, balustrades and entrance surrounds. Bluestone, a dark grey basalt quarried in Victoria, gave Melbourne much of its nineteenth-century character, and sandstone details were a mark of a substantial house.

When the rest of the facade is being repainted, owners sometimes ask whether the stonework should be painted too, either to tidy up staining or to match a new colour scheme. In most cases the answer is no. This guide explains why, what to do instead, and how to handle stone that has already been painted.

Why stone should usually be left unpainted

Stone needs to breathe

Bluestone and sandstone both hold and release moisture. Foundations and plinths in particular draw water up from the ground, and that moisture needs to escape through the face of the stone. Most modern paints form a film that slows or stops that movement. Water then collects behind the paint, carrying salts with it, and as it dries the salts crystallise just under the surface.

On sandstone, which is softer and more porous, this can cause the face of the stone to flake and crumble, a process known as spalling. Once sandstone starts to break down it is difficult and expensive to repair. Bluestone is much harder, but painted bluestone plinths commonly show blistering, peeling and salt staining within a few years.

Paint is very hard to reverse

Paint soaks into the texture of stone, especially sandstone. Removing it later is slow, specialist work and can damage the surface if done the wrong way. An unpainted stone surface keeps all your options open.

Heritage controls may apply

Much of Toorak, Armadale and Hawksburn is covered by heritage overlays. Under Victorian planning schemes, painting a previously unpainted surface on a property in a heritage overlay generally needs a planning permit. If your home is in an overlay, check with the City of Stonnington before anyone puts paint on unpainted stone or brick. Our guide to getting a period-home repaint right covers how overlays affect colour schemes more broadly.

What to do instead of painting

Cleaning the stone

Most of what bothers owners about stonework is dirt, biological growth and old staining. Gentle cleaning usually makes a big difference. Low-pressure washing with suitable cleaners, soft brushes and patience are the right tools. High-pressure blasting and harsh acid cleaners can etch or erode the surface, particularly on sandstone, and should be avoided. Where staining is stubborn, a stone specialist can use poultices designed to draw it out.

Repairing the joints

Crumbling mortar around bluestone foundations lets water in and makes the whole base of the house look tired. Repointing with a lime-based mortar compatible with the original, rather than hard cement mortar, is often the most effective improvement you can make to a plinth. This is usually done by a stonemason or heritage bricklayer before the painters start.

Protecting the stone during the repaint

A careful painter treats stone as a surface to protect. Sills, steps and plinths are masked and covered during preparation and painting, because paint drips and splashes are hard to remove from porous stone. Washdown water from preparing render and timber above is managed so it does not carry paint residue or old lead-paint dust onto the stone.

When the stone has already been painted

Many period homes had their stonework painted decades ago. If the paint is sound and the stone underneath shows no signs of damage, the simplest approach may be to recoat it with a breathable system rather than a standard acrylic. Mineral (silicate) paints and limewash both allow moisture to move through and are well suited to masonry. Breathable finishes like these are part of our feature and decorative finishes work on period surfaces.

If the paint is blistering, peeling or showing salt damage underneath, it is a sign the stone is struggling. Removing the paint, ideally with gentle chemical strippers and low-pressure rinsing chosen by someone experienced with stone, gives the surface a chance to dry out. This is not a job to rush, and it should be tested on a small, discreet area first.

Painting around stone: details that matter

The junction between painted render or brickwork and stone is one of the details that separates a careful repaint from an average one. A clean, straight cut-in line where the rendered wall meets a bluestone plinth, sills left crisp and unpainted, and no smears on the stone all make the facade read properly. On weatherboard homes in Kooyong and Armadale, the bottom board often sits just above a bluestone or brick base, and keeping that line clean matters just as much.

These are the kinds of details we scope as part of our heritage and period-home repaints and weatherboard and render restoration work.

Planning your repaint

When you ask for a quote on a home with stone foundations, steps or dressings, it helps to note which surfaces are stone, whether any of them have been painted, and whether you have noticed flaking, salt marks or crumbling mortar. That lets your painter plan the protection and recommend any specialist cleaning or repointing that should happen first. Leaving the stone as stone, cleaned and well protected, is usually the most respectful and lasting choice for a Toorak home.

Get a Free Quote

Ready to Get Started?

Contact us today for your free, no-obligation quote.

Request a Quote
Get in touch